Macbook A1706 / A1708 Retina Display Assembly In Space Gray
Macbook Complete A1706 / A1708 Screen - Space Gray - OEM Quality Is A Full Top-Lid Display Assembly Ready For Drop-In Replacement On 13-Inch MacBook Pro Models From 2016–2017. It Delivers A 13.3-Inch Retina Panel At 2560 × 1600 Resolution, 227 Ppi, Ips, Led Backlight, And P3 Wide Color For Consistent Color Across Fleets. Brightness Reaches Up To 500 Nits And The Glossy Surface Uses An Anti-Reflective Coating To Reduce Glare Without Muting Contrast. The Space Gray Anodized Finish Matches Factory Hardware So You Can Return Devices To A Uniform Look After Damage Or Delamination.
The Assembly Arrives Factory-Bonded And Pre-Aligned To Cut Bench Time. You Get The Lcd Panel, Backlight, Aluminum Lid, Hinges, Display Flexes, Clutch Cover, Antenna Set, 720p Facetime Hd Camera, Microphone, Sleep Magnet, And Integrated Rubber Gaskets. Color, Brightness, And Backlight Uniformity Are Checked At Production, So You Can Install And Hand Back The Device With Minimal Post-Repair Tuning.
Technical Data And What Is Included
Panel Type Is Ips Led With 60 Hz Refresh And 16:10 Aspect Ratio. Typical Brightness Is 500 Nits With P3 Wide Color Gamut Support And Factory White-Point Calibration Near D65. Surface Is Glossy With Anti-Reflective Coating Camera Module Is Facetime Hd 720p With Integrated Microphone And Cable. Wireless Antennas For Wi‑Fi And Bluetooth Are Pre-Installed In The Hinge Clutch. All Flex Cables Are New And Pre-Routed, Eliminating Rework On Fragile Display Cables.
The Build Is Oem Quality With Precision-Balanced Hinges For Smooth Opening And Consistent Lid Tension. The Hinge Barrels Are Installed And Aligned, And The Hinge Covers Are Fitted. The Finish Is Space Gray To Match 2016–7 13-Inch MacBook Pro Units. The Assembly Ships In An Esd-Safe, Foam-Lined Carton With Protective Films On The Lens And Panel To Prevent Dust Contamination During Handling.
Confirmed Compatibility And Installation Notes
Compatibility Covers MacBook Pro 13-Inch A1706 With Touch Bar (2016–2017) And A1708 Without Touch Bar (2016–2017). Supported Model Identifiers Include Macbookpro13,2 And Macbookpro14,2 For A1706 And Macbookpro13,1 And Macbookpro14,1 For A1708. Relevant Emc References Are 3071 And 3163 For A1706, And 2978 And 3164 For A1708. It Is Not Compatible With Later 13-Inch Models Such As A1989, A2159, A2251, Or A2289, And It Does Not Support True Tone Hardware Introduced In Later Generations.
Installation Is Straightforward For Any Bench Used To MacBook Pro Service. You Will Need P5 Pentalobe For The Bottom Case, T3 And T5 Torx For Display Brackets, And T8 Torx For Hinge Screws. You Should Disconnect The Battery Before Unplugging Display Flexes, Support The Lid When Removing Hinge Screws, And Tighten Hinges Evenly To Maintain Gap Symmetry. You Should Run A Quick Check After Fitment: Backlight And Color Uniformity, Camera Function, Sleep/Wake On Lid Close, And Wi‑Fi/Bluetooth Signal Through The Antennas.
Built For Repair And Refurbishers
This Assembly Speeds Up Turnaround For Cracked Panels, Backlight Failures, Cable Tears At The Hinge, Delamination, Or Cosmetic Lid Damage. You Can Swap The Complete Unit In One Session Without Panel-Level Rebonding, Heat, Or Adhesive Work. Stocking A Single Space Gray Variant Simplifies Inventory For Mixed A1706 And A1708 Fleets, And The Oem Quality Build Keeps Color Matching And Brightness Consistent Across Refurb Batches.
Each Unit Is Function-Tested For Dead Pixels, Brightness Levels, Uniformity, Camera And Mic Operation, And Cable Integrity Before Packing. You Can Install, Clean The Glass, Remove Protection Films, And Deliver A Clean Finish That Matches Original Fit And Feel With Minimal Calibration Work.
The screens are covered with a 2-year warranty. The warranty does not cover man-made damage.
